Performance
Application
Designed for installation on vehicle dashboards to control wiper speed.
Wiper modes
High, low, mist and interval delays of 3, 5, 8, 12, and 17 seconds. High and low speed wiper rate are
determined by the wiper motor selection. Interval delay is achieved by a .5 second activation of the low
speed wiper output (one wipe). Delay cycle is timed from start to start.
Functionality
Refer to actuator motion legend table.
Circuit diagram
Refer to schematic.
Wash motor
Six amps maximum current (12 volts).
Temperature
Operating temperature = -20° to 160°F, storage temperature = -40° to 185°F.
Nominal voltage
12 volts (9 volts minimum, 16 volts maximum)
Electrical/ Environmental
Conforms to SAE J1455 (load dump, reverse polarity, over voltage, inductive switching, mutual coupling,
ESD, cold cranking, and radiated susceptibility).
Relay Coil Resistance
Relay coil resistance = 60 ohms (minimum) for 12 volt systems.
Mounting
Designed to mount in a 22mm x 44mm (.867 +/- 005 x 1.734 +/- .005") dashboard
opening with a panel thickness of .062" to .094" and .108" to .128".
Material
Zytel 72G13 HSIL BK Black Nylon 6/6 13% Glass
Part Marking
Part labeled with GT part number and date code.
Features
The Norgren GT Development Wiper Washer
Controller with integrated wiper delay function is
designed for installation on vehicle dashboards
to control wiper speed and wash functions. The
microprocessor-based device combines the
functions of two or three conventional wiper
controls, and mounts in a standard 22mm x
44mm dashboard cutout.
The Wiper Controller has been custom designed
to control all wiper functions. The multi-function
toggle is used to turn the wiper on and off, and
also varies wiper speed between high, low,
and five intermittent speeds. The lower button
initiates a combined wash and wipe cycle.
Actuator motion legend
Actuator Motion Function
Top Toggle
(On/Off)
In (A) If wiper is off, turn wiper on to low speed. If wiper is on in any mode,
turns wiper off.
Up (B) If wiper if off, turn wiper onto high speed.
If wiper is on, increment wiper to next highest speed.
If held for more than 1 second, wiper enters its longest delay mode.
Down (C ) If wiper is off, turns on to low speed.
If wiper is on, increment wiper to next highest speed.
If held for more than 1 second, wiper enters its longest delay mode.
Bottom Toggle
Bottom Button
(Wash)
In (D) When unit is off or in delay mode and not wiping:
If pressed less than .5 seconds, single low speed dry wipe (mist function).
If pressed more than .5 seconds, unit continues in low speed and washes for
2 seconds +/- .5 seconds (typically 1-2 cycles) after button is released.
After wash stops release, unit continues to cycle in low speed for 3 seconds +/- .5 seconds (typically
2 additional wipe cycles) then unit returns to prior state.
When unit is in low or high speed mode or wiping in delay mode:
If pressed, unit continues in current speed (low or high) and washes for 2
Seconds +/- .5 seconds (typically 1-2 cycles) or until release, unit
continues at current speed or delay.
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document.
© Norgren GT Development Corporaton, 2014
Wiper Washer Controller
1006-11
REV: 8/14 01
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern