Norgren 200 Series Nugget Spool Valves Bedienungsanleitung PDF herunterladen (Seite 34)

Nugget 200 Spool Valves

VAL-10-34

Littleton, CO USA Phone: 303-794-2611 www.norgren.com

Important:

1.Solenoid operated 2-position detent and

nondetent, and 3-position spring centered

valves can be combined in the same stack.

2.Plain stacking valves with common port 1

only and plain valves with common ports 1, 3

and 5 can be combined in one stack if

grouped together at opposite ends.

3.A stack or group of valves with common port

1 only must have isolating plugs installed in

the manifolding exhaust ports (3 and 5)

between each valve and each of the end

plates. Two exhaust port isolating plugs are

furnished with each valve. Installation need

not be specified on orders for factory

assembled stacks as this will be done

automatically.

4.Isolating plugs furnished in the end plate kit

at no extra cost can be placed between two

stacking valves to block the common ports

and separate a section of the valve stack to

accommodate two different input pressures.

One pressure is brought in from the front end

plate and the second pressure from the end

plate in the back. (Specify on order form

under “Special Instructions” where to install

isolating plugs.)

5.Ports 1, 3 and 5 in one end plate can be

plugged if so specified on order under

“Special Instructions”.

Special Instructions – Factory Assembled Stacking Valves

For Ordering purposes the valve stack is oriented as shown in

column two:

Unless otherwise noted:

1.Cylinder (outlet) ports are oriented toward the bottom

2.The 1 2 operator is on the left side, the

1 4 operator on the right side.

3.Valves are listed from the FRONT to

the BACK

Example 1: One stacking valve assembly with common inlet and

exhaust (ports 1, 3 and 5) and junction boxes with

solenoid operators with indicator lights. Isolating plugs

for two different working pressures installed between

valves 4 and 5.

Example 2: One Combination stacking valve assembly without

junction boxes. Valves on one end of stack with

common inlet and exhaust (ports 1, 3 and 5), and on

the opposite end with common inlet only (port 1).

Answer Example 1

Answer Example 2

Note:

Mufflers or filter nuts should be used in all valve body, end plate, or

solenoid operator exhaust ports to prevent entry of dirt and to

reduce the noise level of the exhausting air.

In wet locations, exhaust ports should not face upward to lessen

the possibility of liquids entering the unit.

Valve Special

Pos. No. Quantity Product Number Instructions

1 1 K79DA50-KS6-KM1

2 1 K79DA50-KS6-KM1

3 1 K79DA50-KM6-KM6

4 1 K89EA50-KM8-KM8

Isolating Plugs

Common

Ports 1, 3 & 5

5 1 K79DA50-KM6-KM6

6 1 K79DA50-KM6-KM6

7 1 K79DA50-KM6-KM6

1 13295-50 End Plate Kit

Valve Special

Pos. No. Quantity Product Number Instructions

1 1 K79DA00-KS6-KV2

2 1 K89EA00-KV0-KV0

3 1 K79EA00-KV2-KV2

4 1 K78DA00-KS6-KV2

5 1 K78EA00-KS6-KV2

1 13295-52 End Plate Kit

PORT 3

COMMON

EXHAUST

VALVE 1

VALVE 2

VALVE 3

FRONT

1 4 END

BACK

Common

Exhaust

1 2 END

PORT 1

COMMON

INLET

PORT 2

CYLINDER

PORT

PORT 4

CYLINDER

PORT

PORT 5

Factory Assembled Stacking Valve

Common Inlet & Exhaust

1 2 ... 29 30 31 32 33 34 35 36 37 38

Kommentare zu diesen Handbüchern

Keine Kommentare

Norgren 200 Series Nugget Spool Valves Bedienungsanleitung Seite 34

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Norgren 200 Series Nugget Spool Valves

Verwandte Produkte und Handbücher für Geschirrspüler Miele G 7855